- Nano Express
- Open Access
Facile Synthesis of Novel Nanostructured MnO2Thin Films and Their Application in Supercapacitors
Nanoscale Research Letters volume 4, Article number: 1035 (2009)
Nanostructured α-MnO2thin films with different morphologies are grown on the platinum substrates by a facile solution method without any assistance of template or surfactant. Microstructural characterization reveals that morphology evolution from dandelion-like spheres to nanoflakes of the as-grown MnO2is controlled by synthesis temperature. The capacitive behavior of the MnO2thin films with different morphologies are studied by cyclic voltammetry. The α-MnO2thin films composed of dandelion-like spheres exhibit high specific capacitance, good rate capability, and excellent long-term cycling stability.
In recent years, manganese oxides (MnO2) have attracted considerable interests due to their distinctive physical and chemical properties and wide applications in catalysis, ion exchange, molecular adsorption, biosensor, and energy storage [1–5]. Specifically, manganese oxides have been extensively evaluated as electrode materials for supercapacitors due to their low cost and environmental benignity compared to noble metal oxides such as RuO2 [6–8]. In the development of supercapacitors, nanostructured electrode materials have received great interests as they exhibit higher specific capacitance and rate capability compared to traditional bulk materials. Over the years, various nanostructured manganese oxides, including one-dimensional (1-D) (nanorodes, nanowires, nanobelts, nanoneedles, and nanotubes), two-dimensional (2-D) (nanosheets, nanoflakes), and three-dimentional (3-D) (nanospheres, nanoflowers, hollow urchins) nanostructures, have been synthesized [9–16]. 3-D hierarchical porous structures often produce more active sites and exhibit more favorable electrochemical properties than 2-D and 1-D structures. However, facile synthesis and mass production of complex 3-D nanostructures are still a challenge in the areas of materials science [17–20]. It has been reported that a core-shell structure with spherically aligned nanorods of α-MnO2 can be prepared through a simple room temperature reaction between MnSO4 and (NH4)2S2O8 with a catalyst of Ag+ in an acid solution . A similar method used by Gong et al. is able to synthesize MnO2 hollow urchins with a reactive template of carbon spheres . Wang et al. also reported the synthesis of hierarchical α-MnO2 spheres by the reaction between MnSO4 and K2S2O8 with the addition of CuSO4 in an acidic solution . However, the preparation of 3-D nanostructured MnO2 in the thin film form has never been reported. Since the use of composite electrodes introduces additional undesirable interfaces in the electrode material with the risk of negating the benefits of electrochemistry using nanostructures, thin film electrodes enable us to investigate the electrochemical properties of the active material itself without the influence of binders and conductive additives as required for composite electrodes.
In this paper, we propose the stratagem to synthesize 3-D α-MnO2dandelion-like spheres and 2-D α-MnO2nanoflakes by a reaction between MnSO4and (NH4)2S2O8in a Na2SO4solution at low temperatures. With a platinum (Pt) substrate submerged into the reaction solution, the nanostructured MnO2can be directly deposited on the Pt substrate in the thin film form. The effects of the synthesis temperature on the morphology of the films are investigated, and the capacitive behaviors of nanostructured MnO2thin films with different morphologies are studied and compared.
Synthesis of Nanostructured MnO2
Analytical grade MnSO4, (NH4)2S2O8, and Na2SO4from Sigma–Aldrich were used. A typical synthesis of nanostructured MnO2was performed by dissolving MnSO4, (NH4)2S2O8, and Na2SO4with a molar ratio of 1:1:1 in 30 mL deionized water at room temperature. The concentrations of Mn2+, S2O82−, and SO42−in the solution are the same as 0.1 mol L−1. A Pt substrate was submerged into the solution, while the solution was magnetically stirred in a beaker at room temperature (RT) for 12 h or at 80 °C for 2 h. One side of the Pt substrate was covered with Parafilm, so that MnO2can only be deposited on one side. After the reaction, the Pt substrate was washed using distilled water and then dried in the vacuum at 60 °C overnight.
Structure and crystallinity of thin films were characterized using a Shimadzu XRD-6000 X-ray diffractometer with Cu Kα radiation at a scanning rate of 1°min−1. Surface morphology of the as-deposited thin films was characterized using a Hitachi S-4100 field emission scanning electron microscope (FESEM). Weights of the MnO2thin films were measured using a microbalance with an accuracy of 0.01 mg.
All electrochemical measurements were conducted using a Solartron 1287 electrochemical interface combined with a Solatron 1260 frequency response analyzer. For the electrochemical measurements, a three-electrode cell system composed of a MnO2thin film electrode as the working electrode, a high surface carbon rod as the counter electrode, and an Ag/AgCl reference electrode was employed. The capacitive behaviors of the as-deposited MnO2thin films were characterized by cyclic voltammetry (CV) in 1 M Na2SO4electrolyte at room temperature. CV measurements were performed on the three-electrode cells in the voltage window between 0 and 0.9 V at different scan rates from 20 to 200 mV s−1. Electrochemical impedance spectra (EIS) of different thin film electrodes were measured at the open-circuit potential in the frequency range from 100 kHz to 10 mHz.
Results and Discussion
Figure 1a, b shows the XRD patterns of the MnO2thin films synthesized at different temperatures. Notably, major diffraction peaks in Fig. 1a, b can be indexed as a tetragonal symmetry of α-MnO2with a space group of I4/m (JCPDS Card, No. 44-0141). Comparing Fig. 1a with Fig. 1b, it can be seen that the diffraction peaks in Fig. 1a are sharper and stronger, indicating that the degree of crystallinity of the products is enhanced as the synthesis temperature increases. However, some small impurity peaks observed from both Fig. 1a, b can be indexed as Mn3O4, which is probably due to the incomplete oxidation reaction between Mn2+and S2O82−. The complete formation of MnO2from the solution can be expressed as the following reaction:
α-MnO2 has usually been found to be the product of the oxidation of Mn2+ by S2O82− either through a hydrothermal reaction  or through a mild solution reaction [21–23]. It has been observed in this study that the formation of nanostructured MnO2 is preferred to deposit on the Pt substrate rather than in the solution. Therefore, the preparation of MnO2 thin films (as shown in Fig. 1c) in this study is quite simple and convenient compared with electrochemical deposition, which is usually employed to prepare MnO2 thin films.
The morphologies of the MnO2 thin films synthesized at different temperatures are shown in Fig. 2. It can be seen from Fig. 2a that the film synthesized at RT is composed of uniform microscopic spheres with diameters ranging from 0.5 to 1 μm. The magnified FESEM image (Fig. 2b) shows that these microscopic spheres are composed of nanowhiskers, resulting in a dandelion-like morphology. Li et al.  reported that a core-shell structure microspheres (2–3 μm) of α-MnO2 can be obtained by the reaction between MnSO4 and (NH4)2S2O8 with the addition of AgNO3 catalyst at RT for 1–2 days. The thin shell of this structure is composed of nanorods, and this morphology can only be obtained with the existence of Ag+. Wang et al.  reported that sea urchin-shaped microspheres (~1 μm) of α-MnO2 can be obtained by the reaction between MnSO4 and K2S2O8 with the addition of CuSO4 at 70 °C for 3 days. In the present work, the 3-D hierarchical structure of α-MnO2 can be obtained at RT in a relatively short synthesis time (12 h) without using any AgNO3 or CuSO4 since the addition of catalyst of AgNO3 or CuSO4 may induce Ag+ or Cu2+ impurities in the final MnO2 products . It is assumed that reaction between Mn2+ and S2O82− in the Na2SO4 solution with a Pt substrate is relatively faster compared to the previous studies [22, 23]. It is interesting to observe a morphology evolution of the film, as the synthesis temperature increases. As shown in Fig. 2d, the film synthesized at 80 °C exhibits another type of porous structure with nanoflakes almost vertically aligned on the Pt substrate. The magnified FESEM image (Fig. 2e) shows that the average size of the nanoflakes is about 500 nm, and the thickness of the nanoflakes is less than 50 nm.
The possible formation mechanism for the hierarchical MnO2 spheres is schematically illustrated in Fig. 2c. Generally speaking, the crystal growth process always includes two steps: the initial nucleation stage and following crystal growth stage [25, 26]. Initially, MnO2 colloids are slowly formed and attached to the Pt substrate. After which, the absorbed MnO2 colloids on the Pt substrate tend to aggregate loosely to form spherical appearance due to their high surface energies. Because the reaction temperature is at RT, Gibbs energy for nucleation of new MnO2 sites is low. As a consequence, MnO2 colloids tend to attach on the habit planes of existing MnO2 sites, leading to the formation of 1-D nanowhiskers from the initial colloidal microspheres. With increase in the processing duration, finally dandelion-like 3-D microspheres of MnO2 on the Pt substrate appear. However, on the contrary to Wang’s finding , the increase in reaction temperature in this study is unable to improve the formation of 3-D hierarchical microspheres of MnO2 but leads to the formation of 2-D nanoflakes. This phenomenon can be explained by the change in growth mechanisms as shown in Fig. 2f. When the reaction temperature is increased to 80 °C, the reaction rate is greatly enhanced along with the high rate of adsorption of MnO2 colloids to the Pt substrate. Under such circumstances, in addition to the one-dimentional growth of the nuclei along the low energy direction , the growth of the nuclei along other directions can also happen due to the fast nucleation and adsorption rates of MnO2 at an elevated temperature. Therefore, nanoflakes instead of nanowhiskers form resulting in the morphology evolution.
The 3-D and 2-D nanostructured MnO2 are promising as electrode materials for supercapacitors due to their porous structure, large surface area, and short diffusion length for protons or alkali cations. In order to evaluate the electrochemical properties of the as-deposited thin films, the thin film samples with different nanostructures were characterized in aqueous 0.1 M Na2SO4 electrolyte with CV measurements. The CV curves at various scan rates from 20 to 200 mV s−1 for the sample A and B are shown in Fig. 3a, b (sample A represents MnO2 with dandelion-like sphere morphology, and sample B represents MnO2 nanoflakes). It can be seen that the curves at the low scan rate of 20 mV s−1 for both samples exhibit ideal symmetrical rectangle-like shape indicating ideal capacitive behavior. As the scan rate increases, slight distortion from the ideal symmetrical rectangle shape can be observed from the CV curves for both samples. However, it is clear to see that the distortion from the rectangularity of the CV curves for the sample A is much less than that for the sample B, indicating much better rate performance of the sample A due to its finer nano-architecture. The specific capacitance of the nanostructured MnO2 film can be obtained by the following equation:
where Q is the voltammetric charge, ΔE is the voltage window (0.9 V), and m is the mass of the active material of the electrode. The specific capacitances at different scan rates for both samples are shown in Fig. 3c. At the scan rate 20 mV s−1, the sample A exhibits a much higher specific capacitance of about 230 F/g than 180 F/g of the sample B. As the scan rate increases, the specific capacitance for both samples decreases, which is typical for electrochemically active MnO2 materials. At the highest scan rate of 200 mV s−1, the sample A can maintain 66% of its full capacitance (we set the specific capacitance at 20 mV s−1 as the full capacitance) while the sample B can only maintain 55% of its full capacitance, indicating that the sample A has much better rate capability than that of the sample B. Figure 3d compares the Nyquist plots for the MnO2 thin films with different nanostructures. A depressed semicircle in the high-frequency range corresponding to the charge-transfer resistance, and a straight sloping line in the low-frequency range corresponding to the diffusive resistance can be observed for both samples. As shown in Fig. 3d, it is clear that the sample A has lower charge-transfer resistance and diffusive resistance compared with those of the sample B, confirming the superior capacitive behavior of the sample A. Based on the previous paper by Chou et al. , surface area of thin film can be derived from the double layer capacitance by fitting EIS using equivalent circuit. The calculated surface areas of the sample A and the sample B are about 414 and 125 m2 g−1 respectively. Pseudocapacitance of MnO2 mainly originates from the adsorption of cations in the electrolyte (M+ = Li+, Na+, and K+) on the surface of MnO2 and also possible intercalation/deintercalation of H+ and alkaline metal cations in the bulk of MnO2. Since the 3-D dandelion-like microspheres of the sample A are composed of much finer nanowhiskers with very small size, they provide a much larger surface area per gram and shorter diffusion length for cations, comparing to the relatively large 2-D nanoflakes of the sample B. Therefore, the morphology advantage of sample A explains why it can exhibit a higher specific capacitance and better rate capability than those of the sample B.
The sample A, showing better capacitive behavior in rate capability test, was further investigated for long-term cycling stability. The CV curves at different cycling stages and variation of specific capacitance over 2,000 cycles are shown in Fig. 4a, b. As shown in Fig. 4a, the CV curves for the 1st, 500th, 1000th, and 2000th cycles almost overlapped with each other, indicating excellent cycling stability. After 2,000 cycles, there is no degradation of the capacitive behavior, indicating no significant structural or microstructural changes in the MnO2thin film electrodes. The CV curve after 2,000 cycles is noted to become more symmetrical with the rectangular shape compared with the first cycle, indicating improved capacitive behavior after long time cycling. The specific capacitance of the sample A (as shown in Fig. 4b) slightly decreases for the first 30–40 cycles then starts to increase very slowly with the cycling. As shown in the XRD results, there is a small amount of Mn3O4exist in the film. Mn with a lower oxidation state in the Mn3O4is probably oxidized to Mn4+during the long time CV cycling, resulting in improved capacitive behavior and an small increase of specific capacitance.
MnO2thin films with nanostructures have been prepared on Pt substrates by a facile and mild solution method. The MnO2film prepared at RT with a long reaction time is composed of dandelion-like microspheres, which consists of nanowhiskers with very small size. The reaction temperature plays an important role in controlling the surface morphology of the film. As the reaction temperature was increased to 80 °C, a film composed of nanoflakes can be prepared in a very short time. The CV measurements indicate that MnO2thin films prepared by this method are promising as electrodes for supercapacitors. The film composed of dandelion-like microspheres exhibited a higher specific capacitance and better rate capability than the film composed of nanoflakes, which is probably due to the high surface area and smaller feature of the microspheres. The excellent cycling stability and good rate capability of the film composed of dandelion-like microspheres coupled with the simple and low cost synthesis method make this material attractive for large applications.
Ding YS, Shen XF, Sithambaram S, Gomez S, Kumar R, Crisostomo VMB, Suib SL, Aindow M: Chem. Mater.. 2005, 17: 5382. COI number [1:CAS:528:DC%2BD2MXps1eqsro%3D] 10.1021/cm051294w
Giraldo O, Brock SL, Willis WS, Marquez M, Suib SL, Ching S: J. Am. Chem. Soc.. 2000, 122: 9330. COI number [1:CAS:528:DC%2BD3cXmt1KisLc%3D] 10.1021/ja001860i
Ding YS, Shen XF, Gomez S, Luo H, Aindow M, Suib SL: Adv. Funct. Mater.. 2006, 16: 549. COI number [1:CAS:528:DC%2BD28XislSkurY%3D] 10.1002/adfm.200500436
Yu J, Zhao T, Zeng B: Electrochem. Commun.. 2008, 10: 1318. COI number [1:CAS:528:DC%2BD1cXhtVarsb%2FP] 10.1016/j.elecom.2008.06.028
Subramanian V, Zhu HW, Wei BQ: Electrochem. Commun.. 2006, 8: 827. COI number [1:CAS:528:DC%2BD28XktlGqs7c%3D] 10.1016/j.elecom.2006.02.027
Chou SL, Wang JZ, Chew SY, Liu HK, Dou SX: Electrochem. Commun.. 2008, 10: 1724. COI number [1:CAS:528:DC%2BD1cXht12isrrM] 10.1016/j.elecom.2008.08.051
Prasad KR, Miura N: Electrochem. Commun.. 2004, 6: 1004. 10.1016/j.elecom.2004.07.017
Wu MS, Chiang PCJ: Electrochem. Commun.. 2006, 8: 383. COI number [1:CAS:528:DC%2BD28XhslKlt78%3D] 10.1016/j.elecom.2005.12.014
Xia H, Xiao W, Lai MO, Lu L: Funct. Mater. Lett.. 2009, 2: 13. COI number [1:CAS:528:DC%2BD1MXns1Cnsbg%3D] 10.1142/S1793604709000478
Wang X, Li YD: J. Am. Chem. Soc.. 2002, 124: 2880. COI number [1:CAS:528:DC%2BD38XhsF2qs70%3D] 10.1021/ja0177105
Wu MS, Lee JT, Wang YY, Wan CC: J. Phys. Chem. B.. 2004, 108: 16331. COI number [1:CAS:528:DC%2BD2cXnslGqurk%3D] 10.1021/jp0404955
Cheng FY, Zhao JZ, Song WN, Li CS, Ma H, Chen J, Shen PW: Inorg. Chem.. 2006, 45: 2038. COI number [1:CAS:528:DC%2BD28XpsVGhuw%3D%3D] 10.1021/ic051715b
Ma RZ, Bando Y, Zhang LQ, Sasaki T: Adv. Mater.. 2004, 16: 918. COI number [1:CAS:528:DC%2BD2cXlslektLg%3D] 10.1002/adma.200306592
Xu MW, Kong LB, Zhou WJ, Li HL: J. Phys. Chem. C.. 2007, 111: 19141. COI number [1:CAS:528:DC%2BD2sXhtlKlu77F] 10.1021/jp076730b
Ni JP, Lu WC, Zhang LM, Yue BH, Shang XF, Lv Y: J. Phys. Chem. C.. 2009, 113: 54. COI number [1:CAS:528:DC%2BD1cXhsVyhs7vE] 10.1021/jp806454r
Yan CL, Xue DF: J. Phys. Chem. B.. 2006, 110: 1581. COI number [1:CAS:528:DC%2BD28XitVGktw%3D%3D] 10.1021/jp056373+
Yan CL, Xue DF: Adv. Mater.. 2008, 20: 1055. COI number [1:CAS:528:DC%2BD1cXlt1WmtL0%3D] 10.1002/adma.200701752
Liu J, Xue DF: Adv. Mater.. 2008, 20: 2622. ; COI number [1:CAS:528:DC%2BD1cXptVOrsLc%3D]; Bibcode number [2005JMatR..20.2622L] 10.1002/adma.200800208
Zhao X, Ren X, Sun CT, Zhang X, Si YF, Yan CG, Xu JS, Xue DF: Funct. Mater. Lett.. 2008, 1: 167. COI number [1:CAS:528:DC%2BD1MXjtFCqtrc%3D] 10.1142/S1793604708000393
Li BX, Rong GX, Xie Y, Huang LF, Feng CQ: Inorg. Chem.. 2006, 45: 6404. COI number [1:CAS:528:DC%2BD28XmsFCmtbc%3D] 10.1021/ic0606274
Wang HE, Lu ZG, Qian D, Fang SP, Zhang JF: J. Alloys Compd.. 2008, 466: 250. COI number [1:CAS:528:DC%2BD1cXhtVyksLvK] 10.1016/j.jallcom.2007.11.041
Subramanian V, Zhu HW, Vajtai R, Ajayan PM, Wei BQ: J. Phys. Chem. B.. 2005, 109: 20207. COI number [1:CAS:528:DC%2BD2MXhtV2jsb%2FJ] 10.1021/jp0543330
Xu JS, Xue DF, Zhu YC: J. Phys. Chem. B.. 2006, 110: 17400. COI number [1:CAS:528:DC%2BD28XotFCqsrk%3D] 10.1021/jp0632788
Lu L, Li LP, Wang XJ, Li GS: J. Phys. Chem. B.. 2005, 109: 17151. COI number [1:CAS:528:DC%2BD2MXosVGgs7s%3D] 10.1021/jp052780+
Hu CC, Chang KH, Wu YT, Hung CY, Lin CC, Tsai YT: Electrochem. Commun.. 2008, 10: 1792. COI number [1:CAS:528:DC%2BD1cXht12isrvL] 10.1016/j.elecom.2008.09.011
Chou SL, Chen FY, Chen J: J. Power Sources. 2006, 162: 727. COI number [1:CAS:528:DC%2BD28XhtFSgsLbO] 10.1016/j.jpowsour.2006.06.033
Wei WF, Cui XW, Chen WX, Ivey DG: J. Phys. Chem. C.. 2008, 112: 15075. COI number [1:CAS:528:DC%2BD1cXhtVCrsrrM] 10.1021/jp804044s
This research is supported by National University of Singapore and Agency for Science, Technology and Research through the research grant R-265-000-292-305 (072 134 0051).
About this article
Cite this article
Xia, H., Xiao, W., Lai, M. et al. Facile Synthesis of Novel Nanostructured MnO2Thin Films and Their Application in Supercapacitors. Nanoscale Res Lett 4, 1035 (2009) doi:10.1007/s11671-009-9352-4
- Thin film
- Cyclic voltammetry