Abstract
The vibration behavior of an atomic force microscope [AFM] cantilever with a crack during the nanomachining process is studied. The cantilever is divided into two segments by the crack, and a rotational spring is used to simulate the crack. The two individual governing equations of transverse vibration for the cracked cantilever can be expressed. However, the corresponding boundary conditions are coupled because of the crack interaction. Analytical expressions for the vibration displacement and natural frequency of the cracked cantilever are obtained. In addition, the effects of crack flexibility, crack location, and tip length on the vibration displacement of the cantilever are analyzed. Results show that the crack occurs in the AFM cantilever that can significantly affect its vibration response.
PACS: 07.79.Lh; 62.20.mt; 62.25.Jk
Introduction
Since its invention in 1986 [1], the atomic force microscope [AFM] has become a very powerful tool for studying the surface characteristics of diverse materials on a micro- and nanoscale level [2–4]. In addition, atomic force microscopy can also be applied to nanoscale lithography. AFM-based nanolithography technique has a very high potential for nanofabrication [5–8]. The nanolithography research can be roughly divided into three categories: (1) local electrochemical reactions of silicon and metal, (2) direct atomic and molecular manipulation, and (3) direct nanomachining of the material. The direct nanomachining of material structures has so far been useful for fabricating nanodevices.
The nanomachining technique has been the interest of many researchers. Horng [9] studied the flexural vibration responses of a rectangular AFM cantilever subjected to a cutting force using the modal superposition method. Voigt et al. [10] utilized a chip cantilever system for material processing tasks on the micro- and nanometer scales by the flexural-torsional resonance mode. Recently, Zhu et al. [11] investigated the AFM-based nanometric cutting process of copper using molecular dynamics simulation.
Cracks may occur in the AFM cantilever during the nanomachining experiments or in the fabrication of cantilever [12]. The cantilever with cracks will affect its performance when used. The finite element method and finite difference method can be used to analyze the vibration response of a beam with cracks. For example, Sinha and Friswell [13] investigated the vibration behavior of a free-free beam with a breathing crack using a finite element model. Dorogoy and Banks-Sills [14] utilized a finite difference method to study the effect of contact and friction on the disk specimens containing a crack that are subjected to concentrated loads. Based on our literature survey, however, there has been no investigation on the mechanical properties of an AFM cantilever with cracks. The vibration response of a cantilever is related to the processing quality. In this paper, the vibration behavior of the cracked cantilever during the nanomachining process is studied. An analytical expression of vibration displacement of the cracked cantilever is obtained. Both the finite element and finite difference methods are a numerical method. However, the method adopted in this paper is an analytical model. In general, the solution obtained using the analytical method is more accurate than that of the numerical method. In addition, the effects of crack flexibility and crack location on the displacement are investigated.
Analysis
An AFM probe is used to machine the specimen, and it is considered as a cantilever beam which has Young's modulus E, moment of inertia I, density ρ, the uniform cross-section A, and length L. When the machining is in progress, the cantilever tip contacts with the specimen and induces a vertical reaction force, F y (t), and a horizontal reaction force, F x (t), which are a function of time t. Assuming that the reaction forces are on the tip end, the product of the horizontal force and the tip length can form the equivalent moment exerted on the cantilever. The cutting system can be modeled as a flexural vibration motion of the cantilever. The motion is a partial differential equation, and its transverse displacement is dependent on time t and the spatial coordinate X.
Assume the cantilever has a crack at a distance D from the fixed end, and in the vicinity of the crack, there are no the abrupt change of the cross-section. The rotational spring is used to simulate the crack; the cantilever will be divided into two segments by the spring as shown in Figure 1. The spring is assumed to be massless. The cantilever vibration behavior is changed according to the sample properties when the sample surface is in contact with a cantilever tip. The dynamical behavior is complex and highly nonlinear [15]. Simplification is often realized by modeling the cantilever as a linear approximation for the tip-sample interaction forces or a one degree of freedom system [16, 17]. This paper investigates the vibration behavior of an AFM cantilever with a crack during the nanomachining process. A relatively large force is generated to perform the machining operation. The effects of van der Waals force, surface stress, electrostatic force, and residual stress are assumed to be negligible. Therefore, the governing equation of transverse vibration of the cantilever with a crack can be expressed by the Euler-Bernoulli equation as follows [18]:
where X is the distance along the center of the cantilever, t is time, and Y1(X,t) and Y2(X, t) are the transverse displacement of both segments, respectively.
For compatibility of displacement, moment and shear force of for the two adjacent portions of the cantilever can be expressed by the following jump conditions:
Since, the crack is simulated by a rotational spring; the angular displacement between the two segments can be expressed by the following equation:
where W is the rotational spring constant, and I stands for the mass moment of inertia.
Finally, the boundary conditions for the AFM cantilever are the following [19]:
where H and m are the tip height and mass, respectively; c is the distance between the lower edge of the cantilever and centroid of the cross section. The boundary condition of the cantilever at X = 0 is assumed a fixed end; then, the boundary conditions given by Equations 7 and 8 correspond to conditions of zero displacement and zero slope. The commercial cantilevers are fabricated with a holder providing the base to which the cantilever is suspended. The holder is assumed to be rigid, and the vertical and horizontal reaction forces and fixing moment at the built-in fixed end of the cantilever are to be neglected in the analysis. In addition, the boundary conditions that are given by Equations 9 and 10 correspond to the moment and the force balanced between the beam and a combination of the linear tip-sample stiffness at X = L, respectively. F y (t) and F x (t) which are both functions of time t are denoted the vertical and horizontal cutting force on the sample under the normal and lateral direction, respectively. The first term on right side in Equation 9 represents the moment due to the lateral tip-sample cutting force, and the second term denotes the moment due to the mass moment of inertia of the tip. Similarly, the first term on the right side in Equation 10 is the normal tip-sample interaction force, and the second term is the inertia force of tip mass [19]. The relationship between F x and F y can be expressed as . The relationship is obtained from a geometrical relation for a cone-shape tip, and θ is a half-conic angle [20].
The vertical cutting force is assumed to be as follows:
where Ω is the excitation frequency of the cutting force, and P is the arbitrary constant.
The dimensionless variables are defined as follows:
where v1 and v2 are the dimensionless transverse displacement of the two segments; τ, ε, h, and δ are the dimensionless time, tip mass, length, and centroid of tip, respectively; k c and α are the dimensionless crack flexibility and crack location, respectively; and Λ is the dimensionless excitation frequency in the transverse direction of the cantilever. Accordingly, the dimensionless vertical and horizontal cutting forces are expressed as follows:
where are the dimensionless constants relevant to the cutting force in the vertical direction.
The vibration displacements of the two segments can be assumed in the following forms:
Substituting the harmonic solution given by Equation 14 into Equations 1 to 10 and using the dimensionless variables given by Equation 12, the governing equation and the compatibility and boundary conditions can be simplified to the following dimensionless equations:
The solutions of Equations 15 and 16 can be expressed in the following forms:
where B1...B8 are arbitrary constants, γ is the wave number, and γ4 = Λ2.
Using the compatibility and boundary conditions given in Equations 17 to 23, a 8 × 8 linear system for the AFM cantilever with a crack is obtained:
where
where
If the determinant of A is set to be zero (i.e., ), the wave number γ of the AFM cantilever with a crack will be solved. Then, the dimensionless free vibration frequency ω n will also be obtained by ω n = γ2, while the dimensionless excitation frequency Λ is set as follows:
where r is the frequency ratio. The displacement of the cantilever with a crack can be solved from the equation:
If no crack (i.e., k c = 0) is taken into account in the analysis, the frequency equation can be reduced to the following equation:
The above frequency equation can also be obtained from the result of Wu et al. [19].
Results and discussion
The displacement and frequency of an AFM cantilever with consideration of crack effect for nanomachining is developed as mentioned above. The cutting force in the vertical direction is assumed to be as follows:
During nanomachining process, the vibration displacement of the AFM cantilever is related with the cutting depth and processing quality. In this article, the effects of crack flexibility kc, crack location D/L, and tip length h on the displacement of the cantilever are studied. The following material properties and geometrical parameters are used [5, 19]: L = 300 μm, E = 170 GPa, I = 33.3 × 10-24 m4, A = 10-10 m2, H = 10 μm, ρ = 2,300 kg/m-3, m = 2 × 10-13 kg, c = 2.5 μm, P = 10-8 nN, and fy = 0.16 × 10-3. In addition, the excitation frequency cannot be the same with the natural frequency of the cantilever. Figure 2 shows the vibration displacement which is a function of the fundamental frequency ratio, r, for the AFM nanomachining with D/L = 0.5, h = 1/30, and kc = 0.4. The value of r is defined as the ratio of the excitation frequency to the natural frequency of mode 1 of the cantilever. Using a different value of frequency ratio, we can obtain the different displacements of the AFM cantilever. As expected, a larger vibration displacement is obtained as the r value is closer to1. A larger displacement indicates a larger cutting depth.
Figure 3 depicts the vibration displacement which is a function of crack location for the AFM nanomachining with h = 1/30, kc = 0.4, and r = 0.9. The cantilever has a larger flexibility as the crack is closer to the fixed end. Therefore, the cantilever shows a significant increase in the vibration displacement when the crack is near the fixed end. The crack flexibility indicates crack configuration and crack depth and is related to the changes of natural frequency and displacement of the cantilever. The vibration displacement is a function of crack flexibility for the AFM nanomachining with h = 1/30, D/L = 0.5, and r = 0.9 which is depicted in Figure 4. A crack makes the cantilever locally less stiff because of the added flexibility. Therefore, the displacement of the cracked cantilever increases with the increasing value of crack flexibility. As for the case of kc = 0, it implies no crack in the cantilever so that its displacement is the lowest.
Figure 5 shows the vibration displacement which is a function of tip length for the AFM nanomachining with D/L = 0.5,r = 0.9, and kc = 0.4. A higher tip length results in a larger flexibility. Therefore, it can be found that a higher vibration displacement is obtained when the value of h is larger. Figures 2, 3, 4, and 5 can be used to predict peak displacement. The area under the curve is related to the material removal rate. For a more uniform depth of cut, the flatter curves are better. In addition, D/L ratios, r, and kc are important design parameters of an AFM cantilever with a crack; we can use them to control nanomachining. The change in r is a more effective way to control displacement than D/L or kc.
Conclusions
During the nanomachining process, the effects of crack flexibility, crack location, and tip length on the vibration displacement of an AFM cantilever with a crack were analyzed. According to the analysis, the following results were obtained:
-
1.
The vibration displacement of the cantilever significantly increased when the crack was near the fixed end.
-
2.
The displacement of the cracked cantilever increased with increasing value of crack flexibility.
-
3.
A higher vibration displacement of the cracked cantilever was obtained when the tip length was larger.
References
Binnig G, Quate CF, Gerber C: Atomic force microscope. Phy Rev Lett 1986, 56: 930. 10.1103/PhysRevLett.56.930
Fang TH, Chang WJ, Weng CI: Surface analysis of nanomachined films using atomic force microscopy. Mater Chem Phys 2005, 92: 379. 10.1016/j.matchemphys.2005.01.048
Tosello G, Gava A, Hansen HN, Lucchetta G, Marinello F: Characterization and analysis of weld lines on micro-injection moulded parts using atomic force microscopy. Wear 2009, 266: 534. 10.1016/j.wear.2008.04.077
Ogawa T, Kurachi S, Kageshima M, Naitoh Y, Li YJ, Sugawara Y: Step response measurement of AFM cantilever for analysis of frequency-resolved viscoelasticity. Ultramicroscopy 2010, 110: 612. 10.1016/j.ultramic.2010.02.020
Fang TH, Chang WJ: Effects of AFM-based nanomachining process on aluminum surface. J Phys Chem Solids 2003, 64: 913. 10.1016/S0022-3697(02)00436-5
Fang TH, Chang WJ: Nanolithography and nanoindentation of tantalum-oxide nanowires and nanodots using scanning probe microscopy. Physica B: Cond Matt 2004, 352: 190. 10.1016/j.physb.2004.07.010
Buyukkose S, Okur S, Aygun G: Local oxidation nanolithography on Hf thin films using atomic force microscopy. J Phys D: Appl Phys 2009, 42: 105302. 10.1088/0022-3727/42/10/105302
Martínez RV, Martínez J, Garcia R: Silicon nanowire circuits fabricated by AFM oxidation nanolithography. Nanotechnology 2010, 21: 245301. 10.1088/0957-4484/21/24/245301
Horng TL: Analytical solution of flexural vibration responses on nanoscale processing using atomic force microscopy. J Mater Processing Tech 2009, 209: 2940. 10.1016/j.jmatprotec.2008.06.059
Voigt F, Krohs F, Gerbach R: Flexural-torsional resonance mode of a chip cantilever system: applications to nanomachining. J Vac Sci Technol B 2009, 27: 958. 10.1116/1.3054265
Zhu P, Hu Y, Ma T, Wang H: Study of AFM-based nanometric cutting process using molecular dynamics. Appl Sur Sci 2010, 256: 7160. 10.1016/j.apsusc.2010.05.044
Joshi M, Rao VR, Mukherji S: A novel technique for microfabrication of ultra-thin affinity cantilevers for characterization with an AFM. J Micromech Microeng 2010, 20: 125007. 10.1088/0960-1317/20/12/125007
Sinha JK, Friswell MI: Simulation of the dynamic response of a cracked beam. Comput Struct 2002, 80: 1473. 10.1016/S0045-7949(02)00098-6
Dorogoy A, Banks-Sills L: Effect of crack face contact and friction on Brazilian disk specimens--a finite difference solution. Eng Fract Mech 2005, 72: 2758. 10.1016/j.engfracmech.2005.05.005
Bhushan B (Ed): Scanning Probe Microscopy in Nanoscience and Nanotechnology. 1st edition. New York: Springer Publication; 2010. [Series: NanoScience and Technology] [Series: NanoScience and Technology]
Rabe U, Janser K, Arnold W: Vibrations of free and surface-coupled atomic force microscope cantilevers: theory and experiment. Rev Sci Instrum 1996, 67: 3281. 10.1063/1.1147409
Turner JA, Hirsekorn S, Rabe U, Arnold W: High-frequency response of atomic-force microscope cantilevers. J Appl Phys 1997, 82: 966. 10.1063/1.365935
Singh KV: Transcendental inverse eigenvalue problems in damage parameter estimation. Mechan Syst Signal Processing 2009, 23: 1870. 10.1016/j.ymssp.2008.05.009
Wu TS, Chang WJ, Hsu JC: Effect of tip length and normal and lateral contact stiffness on the flexural vibration response of atomic force microscope cantilevers. Microelectronic Eng 2004, 71: 15. 10.1016/j.mee.2003.08.009
Chang WJ, Fang TH, Weng CI: Inverse determination of the cutting force on nanoscale processing using atomic force microscopy. Nanotechnology 2004, 15: 427. 10.1088/0957-4484/15/5/004
Acknowledgements
The authors wish to thank the National Science Council of the Republic of China in Taiwan for providing financial support for this study under Projects NSC 99-2221-E-168-019 and NSC 100-2221-E-168-018.
Author information
Authors and Affiliations
Corresponding author
Additional information
Competing interests
The authors declare that they have no competing interests.
Authors' contributions
HLL carried out the derivation of the equations and drawing of the figures. WJC carried out the topic selection, the writing of the manuscript, and other works about the submission. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 2.0 International License (https://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Lee, HL., Chang, WJ. Dynamic response of a cracked atomic force microscope cantilever used for nanomachining. Nanoscale Res Lett 7, 131 (2012). https://doi.org/10.1186/1556-276X-7-131
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/1556-276X-7-131