Fabrication and Properties of High-Efficiency Perovskite/PCBM Organic Solar Cells

This work presents a CH3NH3PbI3/PCBM organic solar cell. Organic PCBM film and CH3NH3PbI3 perovskite film are deposited on the PEDOT:PSS/ITO glass substrate by the spin coating method. The performance of the organic solar cells was observed by changing the thickness of CH3NH3PbI3 perovskite. The thickness of a perovskite film can affect the carrier diffusion length in a device that strongly absorbs light in the red spectral region. The short-circuit current density and the power conversion efficiency were 21.9 mA/cm2 and 11.99 %, respectively, for the sample with 210-nm-thick CH3NH3PbI3 perovskite active layer.

In this work, we report the solution process fabrication of perovskite solar cells which comprised an architecture CH 3 NH 3 PbI 3 perovskites formed by a solvent-engineering technology. This study investigated the optical, structural, and surface properties of a perovskite film that is grown on PEDOT:PSS/ITO electrodes by the solvent-engineering technology as functions of thickness in high-performance perovskite solar cells.

Methods
In this study, a PEDOT:PSS (CLEVIOS Al 4083) film was spin-coated on a pre-cleaned ITO substrate at 5000 rpm for 30 s. After spin coating, the film was annealed at 140°C for 10 min. The perovskite layer was deposited by the solvent-engineering technology of 1.2 M PbI 2 and 1.2 M methylammonium iodide (MAI) in a cosolvent of dimethyl sulfoxide (DMSO) and γ-butyrolactone (GBL) (vol. ratio = 1:1) in a glove box filled with highly pure nitrogen. The perovskite solutions were then coated onto the PEDOT:PSS/ITO substrate by two consecutive spin coating steps, at 1000 and 5000 rpm for 10 and 20 s, respectively. At 5000 rpm for 20 s, the wet spinning film was quenched by dropping 50 μl of anhydrous toluene. After spin coating, the film was annealed at 100°C for 10 min. A solution of PCBM was spin-coated on the perovskite layer/PEDOT:PSS/ITO substrate at 3000 rpm for 30 s. Finally, a Ca/Al electrode was completed by thermal deposition with a thickness of 100 nm. Figure 1 schematically depicts the complete structure. The roles of the PCBM film, CH 3 NH 3 PbI 3 film, and PEDOT:PSS film in the cell structure is electron transport layer, active layer, and hole transport layer, respectively.
A field emission scanning electron microscope (FESEM) (LEO 1530) was used to observe the cross section and surface morphology of the cells. Moreover, the current density-voltage (J-V) characteristics were measured using a Keithley 2420 programmable source meter under irradiation by a 1000-W xenon lamp. Finally, the irradiation power density on the surface of the sample was calibrated as 1000 W/m 2 .  Figure 3 shows the XRD patterns of CH 3 NH 3 PbI 3 and PCBM/CH 3 NH 3 PbI 3 perovskite films deposited on PED-OT:PSS/ITO substrates. The spectra in this study reveal two peaks at the position of 28.39°and 31.86°, which correlate well with (220) and (310) planes of the CH 3 NH 3 PbI 3 perovskite phase. This result suggests that the solvent in the PCBM film does not destroy the structure of the underlying CH 3 NH 3 PbI 3 perovskite film during the coating. Figure 4 plots the UV-visible absorption measurements. Figure 4a shows the absorbance spectra of the   3 NH 3 PbI 3 perovskite films with different thicknesses on glass substrates. The CH 3 NH 3 PbI 3 perovskite film with 190-nm thickness is lower than that of the film with 220-nm thickness. In other words, more sunlight can be absorbed to generate excitons in the perovskite film when the thickness increases. Figure 4b shows the absorption spectra of samples with perovskite and PCBM/perovskite films on PEDOT:PSS/ITO substrates. The samples yielded the typical absorption spectrum of CH 3 NH 3 PbI 3 perovskite between 300 and 760 nm due to the band gap of 1.6 eV [29]. As seen, the absorption of PEDOT:PSS/ITO glass substrate in the figure, in the presence of CH 3 NH 3 PbI 3 , was significantly enhanced throughout the visible region, confirming the possibility of the contribution of CH 3 NH 3 PbI 3 to the harvesting of light. To compare with the sample of CH 3 NH 3 PbI 3 on PEDOT:PSS/ITO substrate, for the sample of PCBM/CH 3 NH 3 PbI 3 on PEDOT:PSS/ITO substrate, the absorption of wavelengths in the range 300-500 nm lightly increases, and the absorption of wavelengths in the range 500-760 nm lightly decreases. That may be attributed to the PCBM absorption [30]. Figure 5 plots photocurrent J-V curves of the perovskite solar cell obtained under 100 mW/cm 2 illumination and the AM1.5G condition. The cell has an active area of 5 × 5 mm 2 and no antireflective coating. Table 1 lists the main characteristics of those samples. According to Table 1, the series resistance (R s ) of cell increases when the thickness of the CH 3 NH 3 PbI 3 perovskite film increases, and the thickness of the CH 3 NH 3 PbI 3 perovskite film can affect the carrier diffusion length in a device that strongly absorbs light in the red spectral region. The perovskite solar cell fabricated on the 210-nm-thick perovskite film showed the highest power conversion efficiency (EFF), η = 11.99 % value (J sc = 21.9 mA/cm 2 ) due to increased photocurrent density. From the J-V curve and η value, we can decide that the optimized passivating thickness of the perovskite film is 210 nm thick. However, further increase in thickness of the perovskite film to 220 nm resulted in decrease of η = 9.88 % value (J sc = 22 mA/cm 2 ). Therefore, a film of optimal thickness would absorb more light and yield a higher current. Figure 6 presents the photoluminescence (PL) spectra of the CH 3 NH 3 PbI 3 perovskite films with different thicknesses on glass substrates. The dominant peak located at 1.615 eV (768 nm) corresponds to the optical band gap of the CH 3 NH 3 PbI 3 perovskite films with a direct band gap and can be attributed to the recombination of the near band-to-band (B-B) [29]. When the thickness of the CH 3 NH 3 PbI 3 perovskite film increases, the PL intensity increases. However, under identical experimental conditions, the PL quantum yield of the 220-nm-thick CH 3 NH 3 PbI 3 is greatly reduced. Therefore, it was  found that a more strikingly quenching effect was in the 220-nm-thick perovskite layer than in the 200-nmthick perovskite layer.

Results and Discussion
The hysteresis effect in the perovskite-based solar cells was reported [31][32][33][34]. The reasons may include the collection of excess carrier, defects in materials, ion movement caused by polarization, or ferroelectric effects. Figure 7 shows the current-voltage curves with forward and reverse scans for a solar cell showing hysteresis. The scan parameters are scan speed (0.2 V/s) and delay time (40 ms). As shown in Fig. 7, a hysteresis was observed in the J-V curves of the present cell, 12.04 and 11.52 % for the forward and reverse bias scans. Only a 0.52 % drop in efficiency was observed as compared to that in the forward bias scan. The average values from the J-V curves in reverse and forward scans exhibited a J sc of 21.925 mA/cm 2 , V oc of 0.86 V, and FF of 62.5 %, corresponding to a PCE of 11.78 % under standard AM1.5G conditions. Figure 8 displays incident photon-to-electron conversion efficiency (IPCE) spectrum of the Al/Ca/perovskite/ PEDOT:PSS/ITO substrate (red squares). The integrated product of the IPCE spectrum with the AM1.5G photon flux is also shown (blue squares). The IPCE spectrum shows the expected behavior for a high-performance device based on CH 3 NH 3 PbI 3 . The onset of photocurrent at 800 nm is consistent with the reported band gap of CH 3 NH 3 PbI 3 [29]. The best device also showed a very broad IPCE plateau of over 80 % between 480 and 600 nm, as shown in Fig. 8. Integrating the product of the AM1.5G photon flux with the IPCE spectrum yields a predicted J sc of around 19 mA/cm 2 , which is in agreement with the measured value of around 22 mA/cm 2 .

Conclusions
High-efficiency and low-cost perovskite/PCBM organic solar cells with various thicknesses of CH 3 NH 3 PbI 3 perovskite were fabricated. The PCBM film as the electron transport layer in the cell structure can improve the optical absorption in the wavelength range of 300-500 nm, and the absorption in the wavelength range of 500-760 nm is lightly dropped according to the comparison between the samples of PCBM/CH 3 NH 3 PbI 3 on substrate and CH 3 NH 3 PbI 3 on substrate. The short-circuit current density and the power conversion efficiency were 21.9 mA/cm 2 and 11.99 %, respectively, for the    optimal measured parameters of the sample with 210nm-thick CH 3 NH 3 PbI 3 perovskite.