Skip to main content

High-Efficiency Silicon Inverted Pyramid-Based Passivated Emitter and Rear Cells

Abstract

Surface texturing is one of the most important techniques for improving the performance of photovoltaic (PV) device. As an appealing front texture, inverted pyramid (IP) has attracted lots of research interests due to its superior antireflection effect and structural characteristics. In this paper, we prepare high-uniform silicon (Si) IPs structures on a commercial monocrystalline silicon wafer with a standard size of 156 × 156 mm2 employing the metal-assisted chemical etching (MACE) and alkali anisotropic etching technique. Combining the front IPs textures with the rear surface passivation of Al2O3/SiNx, we fabricate a novel Si IP-based passivated emitter and rear cell (PERC). Benefiting from the optical superiority of the optimized IPs and the improvement of electrical performance of the device, we achieve a high efficiency of 21.4% of the Si IP-based PERC, which is comparable with the average efficiency of the commercial PERC solar cells. The optimizing morphology of IP textures is the key to the improvement of the short circuit current Isc from 9.51 A to 9.63 A; meanwhile, simultaneous stack SiO2/SiNx passivation for the Si IP-based n+ emitter and stack Al2O3/SiNx passivation for rear surface guarantees a high open-circuit voltage Voc of 0.677 V. The achievement of this high-performance PV device demonstrates a competitive texturing technique and a promising prospect for the mass production of the Si IP-based PERC.

Introduction

Improving efficiency is the eternal theme of the solar cell industry, which mainly focuses on two aspects: the optical performance and electrical performance. The front texturing technique is of importance for prompting the optical performance of the device. Inverted pyramid (IP) as an attractive light-trapping structure has attracted considerable attention due to its superior antireflection effect and structural characteristics [1,2,3,4,5,6,7]. To be specific, the incoming short-wavelength light in silicon (Si) IP undergoes triple or more bounces before being reflected away, possessing one or more bounces than that in traditional upright pyramids [7,8,9]. Meanwhile, this inverted pyramid-structured Si will avoid severe recombination losses faced by the nanostructured black Si [10,11,12,13,14,15,16] because of its big and open structural characteristic.

By employing the lithography inverted pyramid textures on the front surface and SiO2 passivation of the rear surface, Green’s group [17] has successfully fabricated a 25.0% efficient passivated emitter and rear local-diffused solar cell (PERL) with an area of 4 cm2. However, the lithography technique is not suitable for mass production because of its expense, low production-capacity, and incompatibility. Recently, many research interests turn to the metal-assisted chemical etching (MACE) large-area inverted pyramids since the MACE technique is simple, low-cost, large-area, and compatible with the current production line [14, 18,19,20,21]. For example, Jiang et al. [7] have reported inverted-pyramids nanostructure prepared by the MACE process followed by a post nanostructure rebuilding solution treatment and the conversion efficiency of IPs based multi-crystalline silicon (mc-Si) solar cells in large size of 156 × 156 mm2 wafers reached up to 18.62%. By utilizing Cu nanoparticles to catalyze chemical etching of Si, Yang et al. [8] have achieved 18.87% efficient IP-structured Si solar cells with a large area. Zhang et al. [9] have fabricated sc-Si solar cell with IP microstructure by modulated alkaline texturing combined with an optimized MACE method and have achieved a 20.19% efficient 1-μm-sized IP-textured device with a large area. So far, the performances of Si IP solar cell with a large area are not yet satisfied suffering from the large-area uniformity of IP morphology, the control of the IP feature size, and the passivation of the device. As a result, the front-optimized Si IP textures together with the rear passivation are expected to improve cell performance further.

In this paper, we successfully fabricated 21.4% efficiency Si IP-based passivated emitter and rear cells (PERC) with a standard solar wafer size of 156 × 156 mm2 by combining the front optimized MACE IP textures with the simultaneous stack SiO2/SiNx passivation for the Si IP-based n+ emitter and stack Al2O3/SiNx passivation for the rear surface. The key to high performance lies in the optical superiority of the IP textures and the reduced electrical losses by the simultaneous passivation of Si IP-based n+ emitter and rear surface. This novel Si IP-based PERC device structure and technique show a great potential in mass production of high-efficiency silicon-based solar cell.

Methods

The device structure of Si IP-based PERC is designed as follows: (i) The Si IP-based PERC n+ emitter is passivated by stack SiO2/SiNx (PECVD) layers as shown in Fig. 1a. The Si IP structures have a good short-wavelength antireflection effect due to more opportunities of three or more bounces; meanwhile, the stack SiO2/SiNx layer provides a further reduced reflectance and an excellent passivation effect for the Si IPs n+ emitter. (ii) The rear reflector is composed of stack Al2O3 (ALD)/SiNx (PECVD) layers and screen-printed Al as shown in Fig. 1a. Stack dielectric layers are designed to optimize the optical properties of long-wavelength by increasing inner rear reflectance while maintaining a good electrical passivation effect, which is attributed to the field- effect passivation of the fixed negative charges in Al2O3 layer and the chemical passivation of hydrogen atoms in SiNx film. In a word, both optical and electrical properties in this design are simultaneously considered to ensure a high performance of Si IP-based PERC.

Fig. 1
figure1

Design and process of the Si IP-based PERC. a Three-dimensional diagram of Si IP-based PERC. b Process flow of the Si IP-based PERC

Commercial 180-μm-thick 156 mm × 156 mm (100)-oriented crystalline silicon (c-Si), boron-doped (1–3 Ω·cm) p-type wafers were used as substrates. After the standard cleaning process, inverted pyramid textures were prepared on the surface of Si wafers as follows: (1) The cleaned Si wafers were immersed in the mixed solutions of AgNO3(0.0001 M)/HF (4 M)/H2O2 (1 M) for 300 s, resulting in porous Si. (2) Si wafers with porous Si were etched in an NH4OH:H2O2:H2O = 1:1:6 (volume) solutions for 200 s to remove the residual Ag nanoparticles. (3) The wafers with porous Si were modified in an HNO3:H2O:HF = 4:2:1 (volume) solution to prepare nanoholes. (4) Inverted-pyramids textures were fabricated on the surface of Si wafer by anisotropic etching of 60 °C-NaOH solutions for 30, 60, and 90 s, respectively.

POCl3 diffuses for 40 min at 800 °C in the quartz tube furnace and then n+ emitter forms on the front of the wafer (M5111-4WL/UM, CETC 48th Research Institute). The sheet resistance of Si IP-based n+ emitter is 105-110 Ω·sq−1. The selective emitter was fabricated on the front surface of the wafer by laser doping (DR-SE-DY70, DR Laser). After the rear surface polished, SiO2 passivation films were prepared by thermal oxidation on the front of silicon wafers. The Al2O3 passivation layers were deposited on the rear surface of wafer by ALD (PEALD-156, HUGUANG Scientific Instruments of Beijing) for ≈ 30 min at 150 °C. The PECVD-SiNx layers were formed by the reaction of NH4/SiH4 (SC-TD-450C). Subsequently, the rear stack passivation layers of Si IP-based wafer were locally ablated by a 532-nm wavelength and 10-ps pulse length laser (DR-AL-Y60, DR Laser), in order to form the 50-μm width and 1-mm pitch local line openings. Finally, the Si IP-based PERC underwent the commercial screen-printing (PV1200, DEK) and co-firing process (CF-Series, Despatch), to form well Ohmic contacts and local BSFs.

The morphologies and structures of the samples were characterized with a JEOL JSM-6390LA scanning electron microscope. The lifetime of the minority carriers was measured by using a Sinton WCT-120. The absorption spectra were determined by FTIR (Tensor 27, BRUKER). The C-V curve is measured by an impedance analyzer (E4900A, KEYSIGHT). The photoluminescence and electroluminescence photos were taken by PL/EL imaging analysis system (LIS-R2, BTimaging). The reflectance spectra, as well as the IQEs and EQEs, were measured on the platform of quantum efficiency measurement (QEX10, PV Measurements). The electrical parameters of the solar cells were investigated by current-voltage (I–V) measurement under the illumination of AM1.5 (Crown Tech IVTest Station 2000). The cell efficiency was measured by using a BERGER Lichttechnik Single Cell Tester.

Results and Discussion

Figure 2a–e shows the top-view SEM images of the different process steps for the silicon surface texturing. Figure 2a shows the 50–80 nm porous Si on the surface of Si wafer etched by MACE method in the mixed solutions of AgNO3/HF/H2O2. Subsequently, the porous Si is modified by the isotropic etching in the mixed aqueous solutions containing HF/HNO3 and turns to be nanohole structures with a diameter of 800 nm as shown in Fig. 2b. Finally, the micron inverted pyramids (IPs) with different sizes (Fig. 2c–e) are obtained by sodium hydroxide in aqueous solution at 60 °C for 30, 60, and 90 s, respectively. From Fig. 2c–e, we can see that after alkali treatment, the IPs structure sizes for three etching time of 30, 60, and 90 s are ~ 1, 1.3, and 1.8 μm, respectively, meaning an increasing size of IP with the increase of alkali treatment time. Also, we notice that the IPs tend to collapse and transit to be the upright pyramids with the increase of the etching time. As known, the inverted pyramids have the advantage of light trapping over upright ones because light will undergo extra one or two bounces in inverted pyramids than that in upright pyramids. Therefore, the structures with shorter etching time are suitable for the light-trapping textures of PV devices because of the advantage in the short-wavelength antireflection. Figure 2f is the compared photos for different surface structures corresponding to Fig. 2a–e.

Fig. 2
figure2

Morphology of the prepared Si inverted pyramid structures (Si IPs-strus). a SEM image of porous silicon obtained by MACE. b SEM image of nanoholes by the following modifications in the HF/HNO3 mixed solutions. ce SEM images of inverted pyramids (cross section in inset) by the etching in aqueous NaOH solution at 60 °C for 30, 60, and 90 s, respectively. f Compared photos for different surface structures corresponding to ae

Now we turn to the optical properties of Si IP-strus. From the reflectance over the whole wavelength range of 300–1100 nm (Fig. 3a), we observe that the porous Si has a low reflection because of the excellent light-trapping performance of nanostructures [22,23,24]. For nanohole structures, the reflectance in the whole wavelength range has an obvious increase, which is attributed to the decrease of density and increase of feature size of nanoholes. After NaOH treatment for 30 s, benefiting from 3–4 bounces between the (111) planes of the IP, the IPs structures display lower reflection over the 300–1100 nm wavelength range, especially in the short-wavelength range of 300–500 nm. With the alkali etching time increasing, the IPs become larger and tend to be the upright pyramids, resulting in an increasing reflectance. When all samples were covered with the same stack SiO2/SiNx coating, the reflectance drop sharply by more than 10%, which is attributed to the combined reflectance from the optical interference of the stack SiO2/SiNx thin films and the surface structures. In this case, the reflection spectra of samples from different processes are mainly different in the wavelength range of 300–600 nm, which is caused by the difference of feature size of IPs. In particular, Si IP-strus covered by the stack SiO2/SiNx layers displays better short-wavelength antireflection ability than the others, indicating the excellent external quantum efficiencies (EQEs) in the short-wavelength range.

Fig. 3
figure3

Optical properties of the prepared Si IP-strus. a The measured reflectance of different surface morphology and b the solar averaged reflectance Rave over the 300–1100 nm wavelength range

Furthermore, we calculate the average solar reflectivity Rave (see Fig. 3b) over the wavelength range of 300–1100 nm and compare the reflectivity of Si IP-strus with other structures corresponding to different intermediate processes shown in Fig. 2a–c. Rave can be calculated by the expression of

$$ R\mathrm{ave}=\frac{\int_{300\ \mathrm{nm}}^{1100\ \mathrm{nm}}\mathrm{R}\left(\uplambda \right)\ast \mathrm{S}\left(\uplambda \right)\ast \mathrm{d}\uplambda}{\int_{300\ \mathrm{nm}}^{1100\ \mathrm{nm}}\mathrm{S}\left(\uplambda \right)\ast \mathrm{d}\uplambda} $$
(1)

where R(λ) and S(λ) denote the measured reflectance and AM1.5 solar photon spectral distribution, respectively. As shown in Fig. 3b, the Raves of porous Si, nanoholes, IPs, and IPs with SiO2/SiNx coating are 8.22, 17.96, 15.18 (group 1—30 s)/17.35% (group 2—60 s)/20.3% (group 3—90 s), and 3.91% (group 1—30 s)/4.48% (group 2—60 s)/5.60% (group 3—90 s), respectively. The Raves show that the IP-strus have a better antireflection ability than nanoholes and show a decreasing trend with the increase of feature size. When IP-Strus are coated by the stack SiO2/SiNx layers, the lowest Rave is 3.91%, revealing an ideal light-trapping structure for the PV device.

The stack SiO2 (~ 2 nm)/SiNx (~ 75 nm) passivation for the Si IP-based n+ emitter is an effective way for achieving well electrical performance of IP-based PERC and their passivation effect [1] and mechanism have been systematically studied in our previous work [14]. To show the electrical superiority of the stack Al2O3/SiNx passivation layers at the rear of our device, we investigate the influence of the different annealing and light-soaking conditions on the effective minority carrier lifetime (τeff) with respect to the injection level (Δn), as shown in Fig. 4a. Notice that the polished Si wafers have the bulk minority carrier lifetime of ~ 350 μs, and the stack Al2O3/SiNx layers are symmetrically deposited on both sides of polished Si wafers. The thickness of inner Al2O3 and the outer SiNx layer is estimated as ~ 3 and ~ 125 nm, respectively. Two annealing conditions are performed in the air atmosphere: 300 °C and 800 °C for 15 min. Then the wafers are illuminated at 25 °C under the full-wave ranged halogen lamp with a power intensity of 50 mW cm−2 for 100 s. As can be seen from Fig. 4a, the 48 μs τeff (300 °C) and 126 μs τeff (800 °C) after annealing are much higher than the 22 μs τeff of the as-deposited Al2O3/SiNx passivated samples at the injection level of 1.2 × 1015 cm−3.

Fig. 4
figure4

a τeff with respect to the injection level Δn at different annealing temperatures for Al2O3/SiNx passivated wafers. The dashed line denotes one sun injection level. b The FTIR spectra of the samples. c C–V curves for the Au/Al2O3-SiNx/Si structure. d Photoluminescence and electroluminescence photos of devices

Importantly, the effective minority lifetime of annealed samples after 100 s of illumination are 230 μs and 150 μs, respectively, much higher than 126 μs and 48 μs before illumination, demonstrating a very clear light-enhanced c-Si surface passivation of Al2O3/SiNx layers. The charge trapping effect during light soaking [25,26,27,28] could be one of the main mechanisms for the light-enhanced c-Si surface passivation of Al2O3/SiNx films. As Al2O3 films are reported to have a negative fixed charge density [29,30,31,32], some of the excess electrons generated by light were likely to be injected or tunneled into trap states in the inner Al2O3 film, resulting in an increased level of field-effect passivation. Interestingly, the light-enhanced passivation effect at 300 °C annealing is better than that at 800 °C, meaning that light-soaking at a lower temperature annealing is a more effective way to the application of PV device.

To study the effect of the annealing process on the surface modification, we compare the Fourier transform infrared spectroscopic (FTIR) absorption spectra of the annealed samples with that of the as-deposition sample. Figure 4b manifests that the Si–N, Si–O, Si–H, and N–H bonds correspond to the stretching absorption peaks at the wavenumbers of ~ 840, 1070, 2200, and 3340 cm−1, respectively. We see that the densities of both the Si–N and Si–O bonds show an obvious increase after annealing; meanwhile, the density of the Si–H bonds increases slightly. The increases of the Si–O and Si–H bond density implies the decrease of the dangling bonds at the interface of Si/SiO2, resulting in a better passivation effect [33]. Also, the annealing process promotes the density of Si–N bonds, indicating a more dense structure which can effectively prevent the out diffusion of H from entering into the environment instead of into Si bulk. However, for excessively high annealing temperature, the H in Si–H and N–H groups can escape from the bulk Si and the dielectric layers to the environment, which causes the decline of the passivation effect. The result of FTIR is consistent with that of the effective minority lifetime.

To further understand the difference of passivation mechanism between thermal annealing and light-soaking treatment, we analysis the density of fixed charges (Nf) and the density of interface traps (Nit) at the interface of Si and Al2O3 (ALD)/SiNx (PECVD) stack layers by using capacitance–voltage (C-V) measurements from a rigorous metal–oxide– semiconductor (MOS) model.

Nf can be obtained from the following equation:

$$ {\mathrm{N}}_{\mathrm{f}}=\frac{{\mathrm{Q}}_{\mathrm{f}}}{\mathrm{S}\times \mathrm{e}}=\frac{{\mathrm{C}}_{\mathrm{OX}}\times \left({\mathrm{V}}_{\mathrm{MS}}-{\mathrm{V}}_{\mathrm{FB}}\right)}{\mathrm{S}\times \mathrm{e}} $$
(2)

where the following expression can calculate VFB

$$ {V}_{\mathrm{FB}}={V}_{\mathrm{MS}}-\frac{Q_f}{C_{\mathrm{OX}}} $$
(3)

Note that S is the area of metal electrode, e is electronic charge, COX is the capacitance of dielectric film layer, VMS is the difference of the work function between the metal electrode and p-type Si, and VFB is flat band voltage.

Using the Lehovec method [34], we can obtain Nit from the C-V curve:

$$ {\mathrm{N}}_{\mathrm{it}}=\frac{\left({\mathrm{C}}_{\mathrm{OX}}-{\mathrm{C}}_{\mathrm{FB}}\right){\mathrm{C}}_{\mathrm{FB}}}{3{\left(\updelta \mathrm{C}/\updelta \mathrm{V}\right)}_{\mathrm{FB}}\mathrm{ekTS}}-\frac{{\mathrm{C}}_{\mathrm{OX}}^2}{\left({\mathrm{C}}_{\mathrm{OX}}-{\mathrm{C}}_{\mathrm{FB}}\right)\mathrm{S}{\mathrm{e}}^2} $$
(4)

where (δC/δV)FB is the slope near-flat band and is taken as the absolute value. CFB, e, and k are capacitance of MOS structure in a flat band, electronic charge, and Boltzmann constant, respectively.

It can be seen from Fig. 4c that the measured C-V curve of the Al2O3/SiNx stack layers shows obvious accumulation region, depletion region, and inversion region. According to the C-V curves and Eq. (24), we obtain the interface properties of the prepared MOS structures, as shown in Table 1.

Table 1 Nf and Nit at the interface between Al2O3/SiNx stack layers and Si

The fixed negative charge densities show a significant increase by an order of magnitude after thermal annealing meanwhile the interfacial states densities significantly decrease, indicating that annealing enhanced the chemical passivation and field-effect passivation of dielectric films. By further light-soaking treatment, the densities of interfacial states keep the same level, while the densities of fixed negative charges increase further. As mentioned above, some of the excess electrons generated by light were likely to be injected or tunneled into trap states in the inner Al2O3 film, which means that light soaking can enhance the field-effect passivation of the dielectric film. Although the value of Nit is high, the sample by 300 °C annealing and 100 s light-soaking has the highest τeff of 230 μs due to the highest Nf of − 2.87 × 1012 cm−2, meaning that field-effect passivation has an advantage over chemical passivation in this case.

Figure 4d shows the photoluminescence and electroluminescence photos of 1, 1.3, and 1.8 μm IP solar cells with the same passivation process. The brightness of the three groups of photos for both photoluminescence and electroluminescence keeps basically the same level, meaning that the three groups of solar cell devices perform equally well in the passivation of defects. That is to say, the passivation process determines the electrical performance of the solar cell instead of the feature size of IPs, which will be confirmed by the following output parameters of the fabricated solar cells.

Based on the excellent optical and electrical performance of the simultaneous SiO2/SiNx stack layers passivated front Si IP-based n+ emitter and Al2O3/SiNx stack layers passivated rear reflector, we fabricated the Si IPs-based PERC.

Figure 5a shows the internal quantum efficiencies (IQEs) and front surface reflections of the fabricated Si IP-based PERCs. We can observe that 30-s alkali-etching IP-based device (group 1—30 s) shows the lowest reflectance in the short wavelength of 300–600 nm due to its smaller feature size of IPs. Importantly, group 1—30 s has the highest IQEs in this wavelength range, and thus yields the highest external quantum efficiencies (EQEs) as shown in Fig. 5b. Also, the fabricated devices display almost the same EQEs in the long-wavelength range because of the same level of reflectance and IQEs in this range. Therefore, group 1—30 s with smaller feature size possesses better output performance than the other two groups, which is further confirmed by the I-V and P-V curves of devices (see Fig. 5c). Figure 5d shows the η of our champion device reached 21.41%, as well as the Voc of 0.677 V, Isc of 9.63 A, and FF of 80.30%. By our knowledge, it is the highest η among MACE-IP-based solar cells. The inset of Fig. 5d is a photograph of the front and rear surface of the champion device.

Fig. 5
figure5

High-performance Si IP-based PERC. a The IQE and reflectance of the Si IP-based PREC with different alkaline etching times. b The EQE of the Si IP-based PERC with different alkaline etching time. c The I–V and P-V curve of the Si IP-based PERC with different alkaline etching time. d I–V and P-V curve of the champion device

Furthermore, Table 2 shows the detailed parameters of the fabricated devices. Obviously, the average Isc (9.63 A) of the group 30 s device is higher than that of the other two groups, which lies in its best anti-reflection ability of front surface as mentioned above. The difference of Iscs mainly determines the output performances of the devices. Besides, the higher FF and the lower series resistance Rs guarantees the higher η of group 30 s. It is worth to note that all the average Vocs of the Si IP-based PERCs are in the range of 674–676 mV, demonstrating that the same excellent passivation for the front and rear surface of all groups. Finally, benefiting from the gain of optical and electrical performance, we have successfully achieved the highest η of 21.4% of Si IP-based PERC solar cell.

Table 2 Detailed output parameters of Si IPs-based PERC

Conclusions

In conclusion, we optimize the morphologies of the MACE Si IPs structures and fabricate the novel Si IPs-based PERC solar cell with a standard size of 156 × 156 mm2 by combining the stack SiO2/SiNx layers coated IPs textures with the stack Al2O3/SiNx passivation of the rear surface. The optical properties show that the solar averaged Rave of IPs textures coated by the stack SiO2/SiNx layers can be up to 3.91%, revealing IPs an ideal light-trapping structure for PV device. Also, the electrical analysis shows that the polished rear surface passivated by the stack Al2O3/SiNx layers possess very high τeff of 230 μs due to the thermal and light-soaking treatment, demonstrating well light-enhanced c-Si surface passivation of Al2O3/SiNx layers. FTIR measurements provide a further explanation for the high τeffs of the rear surface passivated by the stack Al2O3/SiNx layers. Importantly, a high fixed charge density Nf of − 2.87 × 1012 cm−2 is obtained by means of the C-V measurements, which reveals strong field-effect passivation of Al2O3/SiNx layers. Finally, benefiting from the excellent optical and electrical performance at the front Si IP-based n+ emitter and rear reflector, we achieve the highest η of 21.4%, as well as Voc of 0.677 V, Isc of 9.63 A, and FF of 80.30%. The achievement of high-efficiency Si IP-based PERC provides IPs with an effective way to mass production of Si-based high-efficiency solar cells.

Availability of data and materials

The datasets supporting the conclusions of this article are included within the article.

Abbreviations

PV:

Photovoltaic

IP:

Inverted pyramid

Si:

Silicon

MACE:

Metal-assisted chemical etching

PERC:

Passivated emitter and rear cell

PERL:

Passivated emitter and rear local-diffused solar cell

c-Si:

Crystalline silicon

mc-Si:

Multi-crystalline silicon

PECVD:

Plasma-enhanced chemical vapor deposition

ALD:

Atomic layer deposition

Si IP-strus:

Silicon inverted pyramid structures

Rave :

Averaged reflectance

EQE:

external quantum efficiency

τ eff :

The effective minority carrier lifetime

Δn :

The injection level

FTIR:

Fourier transform infrared spectroscopic

N f :

Density of fixed charges

N it :

Density of interface traps

C-V :

Capacitance–voltage

IQE:

Internal quantum efficiency

V oc :

Open-circuit voltage

I sc :

Short-circuit current

FF:

Fill factor

R s :

Series resistance

References

  1. 1.

    Huang ZG, Gao K, Wang XG et al (2019) Large-area MACE Si nano-inverted-pyramids for PERC solar cell application. Sol Energy 188:300–304

    CAS  Article  Google Scholar 

  2. 2.

    Wang Y, Yang L, Liu Y et al (2015) Maskless inverted pyramid texturization of silicon. Sci Rep 5:10843-1-6

    Google Scholar 

  3. 3.

    Mavrokefalos A, Han SE, Yerci S et al (2012) Efficient light trapping in inverted nanopyramid thin crystalline silicon membranes for solar cell applications. Nano Lett 12:2792–2796

    CAS  Article  Google Scholar 

  4. 4.

    Smith AW, Rohatgi A (1993) Ray tracing analysis of the inverted pyramid texturing geometry for high efficiency silicon solar cells. Sol Energy Mater Sol Cells 29:37–49

    CAS  Article  Google Scholar 

  5. 5.

    Moreno M, Daineka D, Roca i Cabarrocas P (2010) Plasma texturing for silicon solar cells: from pyramids to inverted pyramids-like structures. Sol Energy Mater Sol Cells 94:733–737

    CAS  Article  Google Scholar 

  6. 6.

    Llopis F, Tobías I (2005) Influence of texture feature size on the optical performance of silicon solar cells. Prog Photovolt Res Appl 13:27–36

    CAS  Article  Google Scholar 

  7. 7.

    Jiang Y, Shen H, Pu T et al (2017) High efficiency multi-crystalline silicon solar cell with inverted pyramid nanostructure. Sol Energy 142:91–96

    CAS  Article  Google Scholar 

  8. 8.

    Yang L, Liu Y, Wang Y et al (2017) 18.87%-efficient inverted pyramid structured silicon solar cell by one-step Cu-assisted texturization technique. Sol Energy Mater Sol Cells 166:121–126

    CAS  Article  Google Scholar 

  9. 9.

    Zhang C, Chen L, Zhu Y, Guan Z (2018) Fabrication of 20.19% efficient single-crystalline silicon solar cell with inverted pyramid microstructure. Nanoscale Res Lett 13:4–11

    Article  Google Scholar 

  10. 10.

    Toor F, Branz HM, Page MR et al (2011) Multi-scale surface texture to improve blue response of nanoporous black silicon solar cells. Appl Phys Lett 99:2011–2014

    Article  Google Scholar 

  11. 11.

    Lee IJ, Paik U, Park JG (2013) Solar cell implemented with silicon nanowires on pyramid-texture silicon surface. Sol Energy 91:256–262

    CAS  Article  Google Scholar 

  12. 12.

    Jung JY, Um HD, Jee SW et al (2013) Optimal design for antireflective Si nanowire solar cells. Sol Energy Mater Sol Cells 112:84–90

    CAS  Article  Google Scholar 

  13. 13.

    Lin XX, Hua X, Huang ZG, Shen WZ (2013) Realization of high performance silicon nanowire based solar cells with large size. Nanotechnology 24(23):235402

    CAS  Article  Google Scholar 

  14. 14.

    Huang Z, Song X, Zhong S et al (2016) 20.0% Efficiency Si nano/microstructures based solar cells with excellent broadband spectral response. Adv Funct Mater 26:1892–1898

    CAS  Article  Google Scholar 

  15. 15.

    Kafle B, Mannan A, Freund T et al (2015) Nanotextured multicrystalline Al-BSF solar cells reaching 18% conversion efficiency using industrially viable solar cell processes. Phys Status Solidi Rapid Res Lett 9:448–452

    CAS  Article  Google Scholar 

  16. 16.

    Shi J, Xu F, Ma Z et al (2013) Nanoporous black multi-crystalline silicon solar cells: Realization of low reflectance and explanation of high recombination loss. Mater Sci Semicond Process 16:441–448

    CAS  Article  Google Scholar 

  17. 17.

    Zhao J, Wang A, Green M (1999) 24· 5% Efficiency silicon PERT cells on MCZ substrates and 24· 7% efficiency PERL cells on FZ substrates. Prog Photovolt 474:471–474

    Article  Google Scholar 

  18. 18.

    Chen K, Zha J, Hu F et al (2019) MACE nano-texture process applicable for both single- and multi-crystalline diamond-wire sawn Si solar cells. Sol Energy Mater Sol Cells 191:1–8

    Article  Google Scholar 

  19. 19.

    Liu HC, Wang GJ (2013) Fabrication of high anti-reflection nanowires on silicon using two-stage metal-assisted etching. J Renew Sustain Energy 5(5):053115

    Article  Google Scholar 

  20. 20.

    Huang ZG, Lin XX, Zeng Y et al (2015) One-step-MACE nano/microstructures for high-efficient large-size multicrystalline Si solar cells. Sol Energy Mater Sol Cells 143:302–310

    CAS  Article  Google Scholar 

  21. 21.

    Huang BR, Yang YK, Lin TC, Yang WL (2012) A simple and low-cost technique for silicon nanowire arrays based solar cells. Sol Energy Mater Sol Cells 98:357–362

    CAS  Article  Google Scholar 

  22. 22.

    Branz HM, Yost VE, Ward S et al (2009) Nanostructured black silicon and the optical reflectance of graded-density surfaces. Appl Phys Lett 94:98–101

    Article  Google Scholar 

  23. 23.

    Koynov S, Brandt MS, Stutzmann M (2006) Black nonreflecting silicon surfaces for solar cells. Appl Phys Lett 88:88–91

    Google Scholar 

  24. 24.

    Liu X, Coxon PR, Peters M et al (2014) Black silicon: fabrication methods, properties and solar energy applications. Energy Environ Sci 7:3223–3263

    CAS  Article  Google Scholar 

  25. 25.

    Xie M, Yu X, Qiu X, Yang D (2019) Light-soaking enhanced passivation of Al2O3 on crystalline silicon surface. Sol Energy Mater Sol Cells 191:350–355

    CAS  Article  Google Scholar 

  26. 26.

    Liao B, Stangl R, Mueller T et al (2013) The effect of light soaking on crystalline silicon surface passivation by atomic layer deposited Al2O3. J Appl Phys 113(2):1407

    Article  Google Scholar 

  27. 27.

    Maikap S, Tzeng PJ, Wang TY et al (2008) Memory characteristics of atomic-layer-deposited high- κ HfAlO nanocrystal capacitors. Electrochem Solid-State Lett 11:50–52

    Article  Google Scholar 

  28. 28.

    Zafar S, Callegari A, Narayanan V, Guha S (2002) Impact of moisture on charge trapping and flatband voltage in Al2O3 gate dielectric films. Appl Phys Lett 81:2608–2610

    CAS  Article  Google Scholar 

  29. 29.

    J. Benick, Richter A, Li T.-T.A, et al (2010) Effect of a post-deposition anneal on Al2O3/Si interface properties. Photovoltaic Specialists Conference (PVSC), 2010 35th IEEE.

  30. 30.

    Hoex B, Schmidt J, Bock R et al (2007) Excellent passivation of highly doped p -type Si surfaces by the negative-charge-dielectric Al2O3. Appl Phys Lett 91:1–4

    Article  Google Scholar 

  31. 31.

    Lei D, Yu X, Song L et al (2011) Modulation of atomic-layer-deposited Al2O3film passivation of silicon surface by rapid thermal processing. Appl Phys Lett 99:2012–2015

    Google Scholar 

  32. 32.

    Hoex B, Schmidt J, Pohl P et al (2008) Silicon surface passivation by atomic layer deposited Al2O3. J Appl Phys 104:044903-1-12

    Google Scholar 

  33. 33.

    Choi G, Balaji N, Park C et al (2014) Optimization of PECVD-ONO rear surface passivation layer through improved electrical property and thermal stability. Vacuum 101:22–26

    CAS  Article  Google Scholar 

  34. 34.

    Yun M, Arif M, Gangopadhyay S, Guha S (2006) Electrical characterization of polyfluorene-based metal-insulator-semiconductor diodes. MRS Proc 937:0937-M07-08

    Article  Google Scholar 

Download references

Acknowledgements

The study was supported by the Natural Science Foundation of China (61774069 and 11834011), the “333” Project of Jiangsu Province, the “Qinglan” Project of Jiangsu Education Department”, the Open Project of Key Laboratory of Artificial Structures and Quantum Control (Ministry of Education), the Postgraduate Research &Practice Innovation Program of Jiangsu Province (KYCX19_2262, KYCX20_2930), Lianyungang “Haiyan Plan” (2020-QD-012, 2018-QD-019), and the Open-end Funds of Jiangsu Key Laboratory of Function Control Technology for Advanced Materials.

Funding

This work was supported by the Natural Science Foundation of China (61774069), the “Qinglan” Project of Jiangsu Education Department” and Lianyungang “Haiyan Plan” (2020-QD-012).

Author information

Affiliations

Authors

Contributions

KG designed and performed the experiment, part of performance characterization, data processing, and manuscript drafting. YL gave help in the experiment and data processing. YF drew the device diagram. LXS gave help in calculating Nit and Nf at the interface between Al2O3/SiNx stack layers and Si. YFZ, YFC, SZY, and YMW did the devices fabrication and part of the performance characterization of the samples. WZS gave some help in writing the paper. ZGH gave the idea and the experimental guidance for the whole processes and modified the manuscript writing. All authors read and approved the final manuscript.

Corresponding author

Correspondence to Zengguang Huang.

Ethics declarations

Competing interests

The authors declare that they have no competing interests.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Gao, K., Liu, Y., Fan, Y. et al. High-Efficiency Silicon Inverted Pyramid-Based Passivated Emitter and Rear Cells. Nanoscale Res Lett 15, 174 (2020). https://doi.org/10.1186/s11671-020-03404-y

Download citation

Keywords

  • Si solar cell
  • MACE
  • Inverted pyramids
  • PERC
  • High-efficiency